- Joined
- Mar 17, 2022
- Messages
- 498
- Reaction score
- 392
Hello everyone 
Last December I finally purchased my first house and have been very slowly getting things sorted out. I've finally set aside some time to get my whole audio system setup and dialed in, not just pushing out sound. Earlier this week I started playing vinyl every night just to get a feel for how everything sounds and WOW! Does this ever sound bad
. It's SO bright, absolutely melt your face bright to the point most detail is just lost in distortion.
Some of you might have seen my previous thread "My apartment setup" and you'd know how much I loved the sound of that system in the relatively small but very well damped room. I had carpet everywhere and sound diffusion panels right behind the speakers, solid cement walls and floors with all equipment on spikes do isolate any vibration. My new house is very old and has these beautiful oak strip hardwood floors everywhere, the downside is they pickup all the vibrations from both the speakers and subwoofer. It was actually so bad the turntable would pick up the vibrations and play them back through the speakers creating a horrible boomerang like hum. For the moment I just stuck a towel under it, I know it's bad but it works for now.
So now it's time to create solutions to all these issues so my system isn't beat by a $200 sound bar. First off is isolation, I'm installing rubber isolators under the AV cabinet and getting the speaker base plates finished this weekend, they will have isolation feet as well. If necessary I'll build a platform for the turntable to sit on with its own vibration damping but we'll leave that for later.
The walls are all currently bare and will be a huge reflection source so the minimum I can do for now is getting the acoustic panels I already have hung. The hardwood floor around the listening area could do with a thick rug since it's likely a first reflection area. I do have measurement mic but it's currently packed away somewhere and I'll have to figure out how to use it again.
My kitchen opens up directly to the living room so a lot of listening is just done standing when I'm making dinner.
This is the primary sitting area, I think a rug would do well here.
Behind the speakers gives a better overview of the whole room. I'm thinking this archway over the couch is likely also contributing to some of my issues.
Ceiling treatment is 100% on the table, I live alone and I do what I want!
This 21" slot ported subwoofer might be contributing to some vibrations, just a hunch. It might not be the best solution for bass, but it sounds surprisingly clean.
Setup is the same as before, until my Krell KRS2 arrives next week.
Schiit Freya +
Jeff Rowland Model 1 for the panels
Crown XLS for the woofers
Dayton 4X8 DSP for active crossover duty
Behringer EPX2800 for subs
Speaker base plates getting ready for fresh paint, these are 3/8" steel plate.
Last December I finally purchased my first house and have been very slowly getting things sorted out. I've finally set aside some time to get my whole audio system setup and dialed in, not just pushing out sound. Earlier this week I started playing vinyl every night just to get a feel for how everything sounds and WOW! Does this ever sound bad
. It's SO bright, absolutely melt your face bright to the point most detail is just lost in distortion.Some of you might have seen my previous thread "My apartment setup" and you'd know how much I loved the sound of that system in the relatively small but very well damped room. I had carpet everywhere and sound diffusion panels right behind the speakers, solid cement walls and floors with all equipment on spikes do isolate any vibration. My new house is very old and has these beautiful oak strip hardwood floors everywhere, the downside is they pickup all the vibrations from both the speakers and subwoofer. It was actually so bad the turntable would pick up the vibrations and play them back through the speakers creating a horrible boomerang like hum. For the moment I just stuck a towel under it, I know it's bad but it works for now.
So now it's time to create solutions to all these issues so my system isn't beat by a $200 sound bar. First off is isolation, I'm installing rubber isolators under the AV cabinet and getting the speaker base plates finished this weekend, they will have isolation feet as well. If necessary I'll build a platform for the turntable to sit on with its own vibration damping but we'll leave that for later.
The walls are all currently bare and will be a huge reflection source so the minimum I can do for now is getting the acoustic panels I already have hung. The hardwood floor around the listening area could do with a thick rug since it's likely a first reflection area. I do have measurement mic but it's currently packed away somewhere and I'll have to figure out how to use it again.
My kitchen opens up directly to the living room so a lot of listening is just done standing when I'm making dinner.
This is the primary sitting area, I think a rug would do well here.
Behind the speakers gives a better overview of the whole room. I'm thinking this archway over the couch is likely also contributing to some of my issues.
Ceiling treatment is 100% on the table, I live alone and I do what I want!
This 21" slot ported subwoofer might be contributing to some vibrations, just a hunch. It might not be the best solution for bass, but it sounds surprisingly clean.
Setup is the same as before, until my Krell KRS2 arrives next week.
Schiit Freya +
Jeff Rowland Model 1 for the panels
Crown XLS for the woofers
Dayton 4X8 DSP for active crossover duty
Behringer EPX2800 for subs
Speaker base plates getting ready for fresh paint, these are 3/8" steel plate.
Last edited:
. This thing is an absolute work of art both inside and out, the 2 chassis and power brick weigh about 50lb all together. Unfortunately the phono ground got busted in shipping so I need to repair that before really trying it out.
. The RCF is out to get a proper box made.
and here’s the link.
