Search results

Finally it's here !!

**bump** anyone want to share their experience?

Roberto is spot on .. There is a good difference between Ethos and Montis but barely any difference i heard between Montis and Summitx. That is why i got the Montis and the bass is very good. since i use the speaker also as HT setup, the Sub 212 is a treat on the top .. now i use Sub 212 custom...

Thanks, i did sweeps last night with Montis at 0db and found the best SPL still at 180 degree phase on the 212 :) I am preferring the montis at -10db and dealing the level up in 212 if i need to hear more power of the bass, this way the montis really shines at the midrange and above. I might go...

Tip from Peter in this regard, while using custom filter Montis -10db and put the montis bass control to 0db or anything other then -10db. To make sure phase is correct on the sub as it relates to the Montis, have someone stay at the sub while you listen to lower frequency range of a male...

update: Ended up using Montis -10db profile. I found the midrange and high end frequency opens up after putting the montis sub to -10db. The Anthem A5 amp have more room to provide power to the ES panel, then the sub. The improvement in the low range was also better using the 212 instead of the...

Guys, Would like to know if guys who owns the BalancedForce are using the custom filter with their fronts for 2ch music listening setups? http://www.martinlogan.com/balancedforce/custom-filters-firmware.php I have tried both the Montis 0db and -10db profile. Using the 0db profile , the 212...

Update: Loaded the Montis10DB, played around with REW and bass traps and panels and listening position = attached is before and after. This is without PBK. With the Montis0DB profile and Montis set at 0DB, there is hardly any bass sound comes out of the 212.. it seems most work is done by the...

I have actually found different results by putting in on 180 and just the beginning of the 180 degree mark.. which made me to comment 1 o clock position. The Nulls reduced comparing to the first test, but still hanging around. I guess i have to switch off the Montis and just run the REQ sweep...

I have asked two more questions : A. Do my Anthem A5 power amplifier just powers the ES panel of the Montis or it also have some power contribution to the sub? In the forum, a few people are confused about this. B. My 212 just replaced my paradigm Sub15. Paradigm adviced not to use my isotek...

Adding the reply i have received from ML To power filters, yes, you can have too much of a good thing and depending on design of the filters, you can overdamp a line, or create some current on rush limiting. Isotech is an excellent brand so I wouldn’t fear it. Since most sub amps are...

Last night i spent hours dialling down the 212 to get better result in the REW, including rearranging my bass traps. Phase at 1 o clock worked best for my room and 25hz knob didn't made any noticeable difference , therefore left at 0. The level is set for 70db and 80db peak. Now have to do...

Response below from ML: Response below from ML: Hello Sandeep, I do a lot of the setups at shows so was asked to weigh in on these setup questions. First thing to clarify is how the level control works on the Montis. I have seen you also on the MLO site asking some more. I will try and...

Does anyone know if the ML BalancedForce 212 comes with inbuilt power conditioner ? I use ISOtek Evo and Premiere kit and was thinking if i should just get the isotek premiere cord and connect to a good quality surge protector on to a different circuit. I asked the question to Paradigm for my...

Martin Logan BalancedForce 212 - new addition Martin Logan BalancedForce 212 - new addition

I have received my BF 212 and have now downloaded the Montis-10DB custom profile. What i understood that this profile is meant to be used with Montis as you dialled down the Montis Subwoofer bass control to -10DB . There is a setting called Montis0DB as well, which probably means that your...

I have read that bit from the custom filter page. What i understood is that i should apply the Montis-10DB if i set the Montis bass control knob at -10db, that closely equals to shutting down the subwoofer of the Montis and use the ES panel for pure mid and high frequency and let the Sub 212...

Thanks, the AVM60 is dual SUB out and not L & R out. So, as you said, it is ideal to connect it to LFE input of the 212.

Guys, Instead of starting a new thread, thought of posting it here. Getting myself the 212 next week to match with pair of Montis in a HT setup and replacing my Paradigm Sub15. My Anthem AVM60 coming in next week which have dual SUB XLR out. To use the Montis 0DB custom filter in the 212 and...

Dual Power Amplifier shelves - ‪Anthem‬ A5 and ‪Rotel‬ RMB-1075 = Ready for AVM60 7.1.